Security Control Panel FLEXi SP3

Features

Reporting to the security company‘s central monitoring station (CMS):

• Event reporting submitted by the smartphone’s built-in WIFI module or by the 2G/4G mobile modem.
• Complementary devices to transmit messages to the Central Monitoring Station by either an Ethernet cable or VHF/UHF radio waves of the highest priority.
• Any CMS in the network can be added the reports as long as they using TRIKDIS software/IP receiver or any other product that supports SIA DC-09 IP protocol.
• Developed for over 20 years this is an efficient method for transmission of reports to the main and alternative central station receivers may companies offer the best of security to the clients.
• Setting for the condition to send the reports to CMS, first indicating the need to send reports to CMS first and then to the customers only.
• You can also report events to the CMS of different security solutions providers.
• Many message channels are available that grant the user the possibility to set priority of the messages.

Reporting to user:

• By means of Protegus mobile app, which sends immediate alarms about alarm system events when push and special sound notifications are used.
• Event reporting through SMS to 8 cellular numbers.
• Reporting about events through pre-recorded voice notifications using 8 cellular devices.
• Remote control of selected premises’ protection mode (Arm/Disarm/Stay/Sleep).
• Remote control of connected devices (lighting system, automatic gates, ventilation, heating, watering systems, etc.).
• Remote temperature measurement to a video and audio recording system.

Inputs and outputs:

• Four 14 I/O hardware terminals where an individual pin can be either an input (IN) or output (OUT). Input (IN) types: ATZ, EOL, NC, NO.
• Various parameters of resistors can be utilized in EOL and ATZ type circuits. The creation of inputs IN can be expanded to 32 by using keypads, iO-8, and iO-WL expander modules.
• The board two specially reserved outputs: the bell and the LED. The bell is to control the siren, while the LED is to control indicator lights.
• The number of outputs can be expanded to 16 by using iO-8 and iO-WL expander modules.
• Eight operation setting outputs are given. Each output can get a corresponding operational reading, a time-based command, or quality alerts e.g. – thermostat mode.
• One-wire data bus (“1-Wire”) is distinguished to connect temp sensors (up to 8), which could be a thermal or humidity sensor (1), a key fob (“iButton”) reader.
• GRN-YEL data bus transferring data for 8 keypads of the same kind.
• The years  iO series expander modules have been shown to be connected to one of the following data buses: RF-SH radio frequency wireless sensor transceiver, E485 Ethernet module, or T16 VHF or UHF radio frequency transmitter.

Control of the alarm system during its usability:

• 4-digit long control codes (40 in total), which may be used as a coercion code as well. In such a scenario, entering the user code will disarm the alarm, yet a special report will be sent to the CMS indicating that the alarm was disarmed as a result of coercion.
• Control using keypads: SK232LED, Paradox K636, K10H(V) K32+LED, K32LED, K35, Crow keypad CR16, CR-LCD, CZ-Dallas electronic (“iButton”) key reader, TM17 electronic key reader, RFID reader (Wiegand 26/34).
• Remote control via Protegus mobile app, phone call, or SMS.

Easy Installation:

• Manufacture of different size SP3 mounting kits, including the ones with a built-in transformer or impulse power supply, can be done.
• The supplier recommended SP3 a standard operating procedure which was formulated based on the actual practice and many years of knowledge. That helps install a set of systems in 7 out of the 10 small and medium-sized premises by leaving the default settings unchanged.
• Using the new control panel SP3 is possible without having to change the resistors connected to each sensor.
• Available as settings can be backed up as a file to be used in the future.
• Device configuration by USB cable or remotely via TrikdisConfig
• The remote monitoring of the operation of the SP3 panel together with the ability to change the settings is provided by the software. Via TrikdisConfig the remote connections are not only changing the parameters of the SP3 but also watching the deployment of the panel.
• Two access levels provided for parameter settings: installer and administrator.